車頭傳動 HEADSTOCK GEARING
采用同步齒形帶傳動，有效的降低噪音。改變紗線支數、捻度及牽伸倍數的變換齒輪數，應用優化設計，且能互換使用，便于管理。傳動系統采用中央潤滑方法，定期供油。車尾面板上集中了所有電器操作原件，便于操作，同時能顯示運轉狀況下的錠速，輸出速度及捻度。
The use of a timing belt at the inpoutend of the driving shaft makes possible alow noiselevel.The tooth-figure of the Change gears for matching different amount twists and draft Ratios are of optimized design so that the change gears are Interchangeable and management.The application of A centrallu brication system to the transmission parts enables Oiling to be periodic.The control panel of the machine and contains the manipulation elecments for all the electric devices,having the convenience of manual operation to display the spindle speed outlet speed and twist.
自動化程度高
HIGH AUTOMATION
1.紡紗過程中，任何時候關車，能自動適應停車。
Whenever the frame is required to stop during spinning the frame can stop automatically at a proper position.
2.如需提前落紗，能使鋼領板自動下降及適應停車。
If doffer is required in advance.the ring rails will automatically wind down and stop at a proper position.
3.滿管后，鋼領板自動下降及自動適應停車。
For full bobbins,the ring rails will down to starting position automatically.
4.開車前能使鋼領板自動復位。
While starting the machine,the ring rails will reset themselves at starting position automatically.
5.落紗前能自動接通落紗電源。
Before the doffing,the doffer electric source can be connected cutomatically.
6.開車后低速自動切換高速。
After start of machine,the speed is changed from low to high automatically.
 
 
 主要規格與技術參數：
錠數：504；492；480；456；420；408；396；384；96
錠距(mm)：70
錠速(rpm)：10000～17000
鋼領直徑(mm):38;42;45
筒管長度(mm)：180；190；205；230
適紡號數(tex)：6～96
牽伸倍數：10～50
牽伸型式：三羅拉，雙皮圈，搖架加壓
羅拉直徑(mm)：前、中、后均25
粗紗卷裝(mm)：吊錠Φ135×320
　　　　　　　(max)Φ152×406
粗紗架：托錠支承或單層四、六列吊錠支承
電動機：
主電動機　　380伏，15千瓦(456錠及以下)
　　　　　　380伏，17千瓦(456錠以上)
吸風電動機　380伏，1.5千瓦(420錠及以下)
　　　　　　380伏，2.2千瓦(420錠以上)
鋼領板升降電動機：380伏，180瓦
全機長度(mm):L=1890+(N/2-1)×70,(N-錠數)
全機寬度(mm):1000
全機高度(mm):2050